Skip to main content

Laboratory Safety Rules Need To Follow ( Part 1 )

1. Never work alone in the laboratory.  No student may work in the science classroom without the presence of the teacher.

2. Conduct yourself in a responsible manner at all times in the laboratory.

3. Follow all written and verbal instructions carefully.  If you do not understand a direction or part of a procedure, ASK YOUR TEACHER BEFORE PROCEEDING WITH ANY ACTIVITY

4. When first entering a science room, do not touch any equipment, chemicals, or other materials in the laboratory area until you are instructed to do so.

5. Perform only those experiments authorized by your teacher.  Carefully follow all instructions, both written and oral.  Unauthorized experiments are not allowed.

6. Do not eat food, drink beverages, or chew gum in the laboratory.  Do not use laboratory glassware as containers for food or beverages

7. Be prepared for your work in the laboratory.  Read all procedures thoroughly before entering the laboratory.  Never fool around in the laboratory.  Horseplay, practical jokes, and pranks are dangerous and prohibited.

8. Always work in a well-ventilated area

9. Observe good housekeeping practices.  Work areas should be kept clean and tidy at all times

10. Be alert and proceed with caution at all times in the laboratory.  Notify the teacher immediately of any unsafe conditions you observe.

11. Dispose of all chemical waste properly.  Never mix chemicals in sink drains.  Sinks are to be used only for water. Check with your teacher for disposal of chemicals and solutions.

12. Labels and equipment instructions must be read carefully before use.  Set up and use the equipment as directed by your teacher.

13. Keep hands away from face, eyes, mouth, and body while using chemicals or lab equipment.  Wash your hands with soap and water after performing all experiments.

14. Experiments must be personally monitored at all times.  Do not wander around the room, distract other students, startle other students or interfere with the laboratory experiments of others.

15. Know the locations and operating procedures of all safety equipment including: first aid kit(s), and fire extinguisher.  Know where the fire alarm and the exits are located

16. Know what to do if there is a fire drill during a laboratory period; containers must be closed, and any electrical equipment turned off.

17. Any time chemicals, heat, or glassware are used, students will wear safety goggles. NO EXCEPTIONS TO THIS RULE!

18. Contact lenses may be not be worn in the laboratory.

19. Dress properly during a laboratory activity.  Long hair, dangling jewelry, and loose or baggy clothing are a hazard in the laboratory.  Long hair must be tied back, and dangling jewelry and baggy clothing must be secured.  Shoes must completely cover the foot.  No sandals allowed on lab days.

20.   Report any accident (spill, breakage, etc.) or injury (cut, burn, etc.) to the teacher immediately, no matter how trivial it seems.  Do not panic

21. A lab coat or smock should be worn during laboratory experiments








Comments

Popular posts from this blog

Young’s Modulus ‘Y’ By Searle’s Method

Aim:  To determine Young’s modulus of elasticity of the material of a given wire by Searle’s method.  Procedure: i. Arrange the experimental set up as shown in diagram. Attach a zero load (slotted hanger it self) and dead load (E) to the frames of the experimental wire and dummy wire respectively so that the wires become free of kinks and remain vertically straight. ii. With the help of micrometer screw gauge, find the correct diameter of the wire at three different places. At every place two readings of the micrometer are taken while holding it in one position and another perpendicular to it by rotating through 90°. iii. In all, six readings of the diameter of the wire are taken. Hence mean diameter and radius of the wire is found out. iv. Adjust the spirit level so that the air bubble is at the centre. Note down the reading of the micrometer screw (M) attached to it. This is zero reading. (This contains main scale reading and circu

SAFETY IN THE PHYSICS LABORATORY

In the physics laboratory, carelessness can lead to accidents causing injury to you or to your neighbor. Some instruments are costly. If such an instrument is damaged in an accident, it can paralyze the work of the whole class. Proper handling of apparatus and other materials can prevent majority of accidents.  Remember the following points and act on them, while working in the physics laboratory. (i) Put off the gas to extinguish the flame of a burner. Do not use any solid or liquid for this purpose (like putting a cap or pouring water as for extinguishing burning coal). (ii) Do not throw any broken glass ware, etc. in the sink. Such things should be thrown into the waste basket. (iii) Do not talk to other students in the laboratory while performing the experiment. In case you have any difficulty, consult your tutor. Of course, if you are a team of two or three students working on same experiment on the same apparatus, you can talk about the experiment among yourselve

Spectrometer I - Refractive index of the prism.

PROCEDURE: I. To determine the angle of the prism 1. The preliminary adjustments for telescope, prism and the collimator are done. 2. The slit is illuminated by a sodium vapour lamp. The prism table is mounted vertically. 3. The refracting edge of the prism placed facing the collimator. 4. The image on one side is seen through through the telescope and the vernier readings (R1) are noted. 5. The image on other side is seen through through the telescope and the vernier readings (R2) are noted. 6. 2A = R1  R2  hence the angle of the prism ‘A’ is determined using A =  II. To determine the angle of minimum deviation 1. The edge of the prism is placed facing away from the collimator. 2. The refracting image is obtained in the telescope. The prism table is slowly rotated. 3. The image moves, then stops and turns back. The position of the image where the image stops and turns back is the minimum deviation. 4. The vernier readings (R3) are noted at this position and the direct ray reading